Seawater intrusion and mixing in estuaries

From MarineSpecies Introduced Traits Wiki
Jump to: navigation, search


Estuaries are generally defined as semi-enclosed transition zones between river and sea. The intrusion of seawater in estuaries is mainly due to tides and buoyancy (related to the density difference between seawater and river water, see Estuarine circulation). Seawater intrusion in estuaries is an important phenomenon to man and nature: it limits fresh water availability for human and agricultural use and it determines the type of habitats and species that can develop in an estuarine environment. Besides, density driven currents and salinity play a role in estuarine turbidity and sedimentation processes.

The net effect of estuarine mixing processes during a tidal cycle on along-channel seawater intrusion or on net along-channel spreading (diffusion) of dissolved substances is generally called longitudinal dispersion. This net effect is described by a longitudinal dispersion coefficient [math]K_x[/math]. The different mixing processes contributing to longitudinal dispersion are termed dispersion mechanisms. In well-mixed and partially mixed estuaries these mixing processes are dominantly induced by tidal motion; the net effect on seawater intrusion is called tidal longitudinal dispersion or simply tidal dispersion. We describe in this article the physical processes involved in seawater intrusion and mixing in estuaries under the influence of tidal motion and explain some simple methods for deriving quantitative estimates. Several of the dispersion mechanisms discussed in this article are illustrated by dye experiments shown in Estuarine dispersion: dye experiments in the Eastern Scheldt scale model.

Definitions and assumptions

The estuarine mouth is defined as the transition between zones of channeled tidal flow (main currents following the channel axis) and two-dimensional flow (currents deviated along the open coast). The estuarine head is defined as the transition between the zone where the current has a substantial oscillating tidal component and the zone where river discharge is strongly dominant. We are interested in the net effect of tidal mixing processes during a tidal cycle on seawater intrusion along the estuarine axis, defined as the [math]x[/math]-axis ([math]x=0[/math] at the estuarine mouth). This makes sense only if we assume that the salinity difference between the estuarine mouth and the estuarine head is much greater than salinity differences in lateral ([math]y[/math]-axis) and vertical ([math]z[/math]-axis) directions. Estuaries where salinity differences between bottom and surface are comparable to the salinity differences between estuarine mouth and estuarine head are dealt with in the article Salt wedge estuaries. The estuaries considered in this article are often designated as well-mixed or partially mixed estuaries.

Successive tidal cycles are not identical. Determining the net effect of tidally induced mixing processes requires integration over a large number of tidal cycles. To prevent this complication, we assume that successive tidal cycles are sufficiently comparable (no extreme spring-neap variation) to enable the definition of a representative cyclic tide. This assumption will be used throughout this article.

Random walk

Estuarine mixing processes can be described in terms of random walk. For simplicity we consider a tidal basin with no significant river inflow. Water motion is described as the average motion of a very large number of individual water parcels. If individual water parcels follow identical paths during flood (inflow) and ebb (outflow) all seawater parcels entering the basin during flood will be expelled during ebb: no seawater intrusion will occur. In reality this will not happen; mixing processes ensure that individual water parcels follow different paths during flood and ebb. Water parcels move some time forth and back in a tidal basin before they are evacuated offshore. We call [math]T_x[/math] the flushing time of water parcels in the tidal basin (the average residence time fluid parcels entering the estuary at the upstream boundary). During this time, water parcels also move in lateral and vertical directions, due to flow circulations and turbulent eddies. The time scale for vertical mixing, [math]T_z [/math], and the time scale for lateral mixing, [math]T_y [/math], are related to the vertical and lateral turbulent diffusion coefficients, [math]K_z [/math] and [math]K_y [/math], by the relationships [math]T_z=D^2/K_z [/math] and [math]T_y=B^2/K_y [/math], respectively. The time scales [math]T_y [/math] and [math]T_z [/math] indicate the time during which the motions of individual water parcels remain correlated; after a longer time they have lost the memory of their initial position [math](y,z)[/math] in the estuarine cross-section. The probability that they move after this time to a position in the cross-section from where water parcels experience a net landward displacement during a tidal cycle is the same as the probability of moving to a position from where they experience a net seaward displacement. The cross-sectional mixing time [math]T_A [/math] is approximately equal to the lateral mixing time [math]T_y[/math], if we assume that lateral mixing takes more time than vertical mixing; this is the case for most well-mixed or partially mixed wide estuaries. If [math]T_A[/math] is much smaller than the longitudinal flushing time [math]T_x[/math] of water parcels in the estuary, the longitudinal path of a water parcel follows a random walk. The longitudinal displacements [math]X (1), X (2), … [/math] in successive time intervals [math]\Delta T[/math] are uncorrelated, by choosing [math]\Delta T=nT[/math] equal to an integer number of cyclic tidal periods such that [math]\Delta T \ge T_A[/math]. After a time [math]\tau[/math] comprising a large number [math]N[/math] of time intervals [math]\Delta T[/math] the average net displacement of all water parcels initially situated in a given cross-section of the tidal basin is approximately zero:

[math]E[\sum_{i=0}^N X (i)] \; \approx \; 0 , \qquad(1)[/math]

where [math]E[..][/math] is the ensemble average over all water parcels initially situated in a given cross-section of the tidal basin. Here we have assumed [math]\tau \le T_x[/math]. Because [math]X(i)[/math] and [math]X(j)[/math] are uncorrelated for [math]i \ne j[/math], we have [math]E[X(i)X(j)] \approx 0 \;[/math] for [math]i \ne j[/math] and [math]E[X(i)^2] \approx \overline{X^2} \;[/math] is the average square displacement over a time [math]\Delta T[/math]. The average square displacement over the time interval [math]\tau =N \Delta T[/math] is therefore given by

[math]E[(\sum_{i=0}^N X (i))^2] \; = \; E[\sum_{i=0}^N X (i) \; \sum_{j=0}^N X (j)] \; \approx \; \sum_{i=0}^N E[X (i)^2] \; \approx \; \tau \; \overline{X^2} / \Delta T \qquad(2)[/math].

Figure 1: Longitudinal dispersion coefficients at different locations in the Eastern Scheldt and Ems-Dollard estuaries.

The square of the average displacement of water parcels in the tidal basin thus increases linearly with time. This is precisely the characteristic of a diffusion process of a dissolved substance with concentration [math]s(x,t)[/math]. This diffusion process is described by the equation[1]

[math]\Large \frac{\partial s}{\partial t} \normalsize = K_x \Large \frac{\partial^2 s}{\partial x^2} \normalsize , \quad [/math] with diffusion coefficient [math]\quad K_x = \Large \frac{\overline{X^2} }{ 2 \Delta T} \normalsize \qquad(3)[/math].

The random walk assumption [math] T_x \gt \gt T_A[/math], expressing the condition that particle paths become uncorrelated for time intervals larger than the cross-sectional mixing time [math]T_A[/math] but much smaller than the longitudinal mixing time [math]T_x[/math], thus implies that salt transport by seawater intrusion processes, [math]Q_{disp}[/math], can be represented by a gradient-type transport formula,

[math]Q_{disp} = - A_0 K_x \Large \frac{ds_0}{dx} \normalsize , \qquad(4) [/math]

where [math]s_0[/math] is the tidally averaged salinity concentration, [math]K_x [/math] is the longitudinal dispersion coefficient and [math]A_0=\lt A\gt [/math]. The dispersion coefficient [math]K_x [/math] has the important property that it does not depend explicitly on the salinity distribution in the estuary [2], but only on the flow characteristics during the tidal cycle (which may be influenced by the salinity distribution, by the way). The magnitude of the random displacements depends on the location [math]x [/math] in the estuary; the longitudinal dispersion coefficient [math]K_x[/math] is thus a function of [math]x [/math]. This is illustrated in figure 1 for the Eastern Scheldt and Ems-Dollard estuaries.

Longitudinal dispersion mechanisms

Mixing processes, such as those described by the random walk model, cause seawater to intrude further and further into the estuary. However, seawater is also expelled from the estuary due to the inflow of river water at the estuarine head. Seawater intrusion is stabilised when the net upstream salt transport by mixing processes equals the net downstream salt transport by the fluvial discharge. This can be represented by the following formulas.

The fresh water discharge [math]Q_R[/math] is given by

[math]Q_R=-\lt A\overline{\overline{u}}\gt \equiv - \large \frac{1}{T}\int_0^T \int_{-B/2}^{B/2} \int_0^D \normalsize u(x,y,z,t) dzdy dt \qquad(5) [/math]

and the net total salt flux (by mixing processes and river discharge) is given by

[math]Q_S=\lt A\overline{\overline{us}}\gt \equiv \large \frac{1}{T} \int_0^T \int_{-B/2}^{B/2} \int_0^D \normalsize u(x,y,z,t)s(x,y,z,t) dzdydt , \qquad(6) [/math]

where [math]A(x,t)[/math] is the estuarine cross-section, [math]D(x,y,t)[/math] the instantaneous local water depth and [math]B(x,t)[/math] the estuarine width, [math]u[/math] the longitudinal current velocity and [math]s[/math] the salinity. The brackets stand for averaging over the tidal period [math]T[/math] (assuming a cyclic tide) and the overbars stand for averaging over the depth and the width. The coordinate [math]x[/math] follows the upstream positive longitudinal direction (along the thalweg), the coordinate [math]y[/math] the lateral direction and the coordinate [math]z[/math] the upward positive vertical direction.

We call [math] s_0 \equiv \lt \overline{\overline{s}}\gt [/math] the salinity averaged over the estuarine cross-section [math]A[/math] and the tidal period. We may then decompose

[math]Q_S=Q_{disp} - Q_R s_0, \quad Q_{disp} = \lt A\overline{\overline{u(s-s_0)}}\gt \qquad(7) [/math] .

This decomposition singles out the fresh water discharge (the term [math] Q_R s_0[/math] ) as a mechanism for flushing seawater out of the estuary, while the term [math] Q_{disp}[/math] represents the sum of all processes contributing to seawater intrusion. These processes are:

  • Horizontal circulations in the estuary (mainly the net relative displacement of water masses circulating between ebb and flood channels and the net relative displacements due to geometry-induced eddies, followed by lateral mixing of these water masses);
  • Horizontal tidal straining (lateral mixing between water masses which are advected at different speeds, due to lateral gradients in the longitudinal velocity);
  • Vertical circulation in the estuary, also called estuarine circulation (seawater intrusion induced by the density-driven net displacement of near-surface water relative to near-bottom water, followed by mixing over the vertical);
  • Vertical tidal straining (vertical mixing between water masses advected at different speeds due to vertical gradients in the longitudinal velocity);
  • Lateral mixing of water masses captured in "dead zones" with the main flow;
  • Chaotic dispersion, related to the chaotic character of particle trajectories when travelling through a complex field of tide-generated eddies;
  • Tidal pumping at the inlet (here defined as the partial replacement of the ebb tidal prism with ‘new’ seawater flowing in from the nearshore zone during flood).

Analytical expressions for the longitudinal dispersion coefficient

Under certain simplifying conditions it is possible to derive analytical expressions for the longitudinal dispersion coefficient. These assumptions are:

  • the estuarine geometry does not vary strongly in [math]x[/math]-direction over distances comparable to or larger than the tidal excursion;
  • the cross-section of the estuarine main channel has approximately a rectangular shape.

We also have the condition [math]T_A\lt \lt T_x[/math]. In the following we consider different seawater intrusion processes under these conditions and present an approximate analytical expression for the dispersive transport produced by each process.

Dispersion by residual circulation

Fist we consider seawater intrusion caused by estuarine circulation: the up-estuary near-bottom flow caused by the higher density of seawater relative to estuarine water. The estuarine circulation is represented by the velocity component

[math]u_0 (z)= \lt u\gt -\lt \overline{u}^z\gt , \qquad(8) [/math]

where the brackets [math]\lt u\gt [/math] stand for averaging over the tidal period (in fact, the averaging is done in a frame moving with the cross-sectional mean velocity), and [math]\overline{u}^z [/math] for averaging over the vertical. The longitudinal dispersive transport can be estimated by a procedure outlined by G.I.Taylor [3]. The result is

[math]K_x = f_0^{(z)} T_z \overline{(u_0)^2}^z , \qquad(9) [/math]

with [math] f_0^{(z)} [/math] a coefficient of the order of 0.1 [4].

For the dispersion coefficient related to lateral horizontal residual circulation a similar formula can be derived, replacing in the expression for [math]K_x [/math] everywhere [math]z[/math] by [math]y[/math].

Estuarine circulation is an important seawater intrusion mechanism in estuaries with a single deep (dredged) channel and small to moderate tide. Lateral circulations are important in wide natural estuaries with a complex geometry (meandering main channel , secondary channels, channel bars and tidal flats) and strong tides. The dominance of lateral circulations for seawater intrusion relative to vertical circulations appears in the analytical expression of [math]K_x [/math] through the much larger lateral mixing time [math]T_y [/math] compared to the vertical mixing time [math]T_z [/math]. The presence of distinct ebb and flood channels is a major cause of lateral circulation in wide estuaries, see for example figure 2. However, density gradients related to seawater intrusion also produce lateral circulations (see Estuarine circulation), which contribute often even more to longitudinal dispersion than the vertical density-induced circulation [5].

Figure 2: Circulation cells in the Western Scheldt related to ebb- and flood-dominated channels.

Dispersion by tidal straining

If residual circulations are weak, dispersion is mainly caused by tidal straining, the relative displacement of water masses due to vertical and horizontal gradients in the tidal current velocity. In river flow, the usual term for this mixing mechanism is shear dispersion. Seawater intrusion in narrow deep estuaries is primarily caused by vertical tidal velocity gradients, whereas lateral tidal velocity gradients are important in wide estuaries. We present formulas for vertical tidal straining; the expressions for lateral tidal straining are similar. The process of longitudinal dispersion through tidal straining is explained in figure 3.

The velocity component [math]u_1 (z,t) [/math] responsible for vertical tidal straining is

[math]u_1= u-\overline{u}^z , \qquad(10) [/math]

where [math]\overline{u}^z[/math] is the depth-average current velocity. By a procedure outlined by Holley, Harleman and Fischer [6], the following first-order estimate of the longitudinal dispersion coefficient is obtained:

[math]K_x \approx f_1^{(z)} \Large \frac{T_z \lt \overline{ u_1^2}^z\gt }{1+( f_2^{(z)} T_z / T)^2 } \normalsize \qquad(11) [/math] .

The coefficients [math] f_1^{(z)}, f_2^{(z)} [/math] depend on the velocity profile; order-of-magnitude estimates are [math] f_1^{(z)} \sim 0.1-0.2[/math] and [math] f_2^{(z)} \sim 0.5-1 [/math].

Longitudinal dispersion produced by lateral tidal straining can be expressed by a formula similar as for vertical tidal straining. Dispersion by tidal straining is largest if the time scale for vertical or lateral mixing is on the order of [math]T/ f_2[/math]. The time scale for vertical mixing is generally smaller than the tidal period and the time scale for lateral mixing is generally larger. Dye experiments illustrating dispersion by lateral tidal straining are shown in Estuarine dispersion: dye experiments in the Eastern Scheldt scale model.

It should be realised that longitudinal dispersion is not simply the sum of transport processes related to circulation and straining. Circulation causes not only a net relative displacements of water masses in the estuary, but it also influences tidal straining.

Figure 3: Schematic representation of longitudinal dispersion by a vertical gradient in the tidal current [math]u(z,t)[/math]. A patch of dye is introduced homogeneously over the vertical when flood starts at low water slack tide ([math]t=0[/math]). The patch of dye is stretched by the tidal current while being mixed vertically by turbulent diffusion. The time scale for vertical mixing [math]T_z[/math] is assumed equal to the tidal period [math]T[/math]. The tidal cycle is represented by four discrete time steps, illustrating the longitudinal spread of the patch of dye.

Dispersion by “dead zones”

The formula for lateral tidal straining includes the influence of "dead zones", if they are considered part of the estuarine cross-section and if they are distributed regularly along the estuary. Dead zones are areas along the main estuarine channel where water is not transported in longitudinal direction, for instance, tidal flats or lateral creeks. The longitudinal dispersion coefficient is given by an expression of the type [7]

[math]K_x=f_{dz}rU^2T , \qquad(12) [/math]

where [math]U[/math] is the maximum tidal velociy and [math]r[/math] is the high-water (HW) storage cross-section of the dead zones relative to the channel cross-section. The coefficient [math]f_{dz}[/math] depends on the mixing rate within the dead zone; in case of complete mixing during the tidal cycle [math]f_{dz}=1/12 \pi^2[/math], assuming that filling of the dead zones starts at low water (LW) [8].

Even without any mixing, storage areas along the channel contribute to longitudinal dispersion, because of a non-zero phase shift [math]\phi[/math] that generally exists between horizontal and vertical tidal motion (between [math]u(t)[/math] and [math]d\eta /dt[/math], respectively, where [math]\eta(t)[/math] is the tidal level). The process is illustrated in figure 4. We assume dead zones with bed level at low water (or below), which are distributed evenly along the estuarine main channel. Filling and emptying of the dead zones during the tidal period then produces a net transport through a plane at [math]x=0[/math] given by

[math]Q_{disp} = - \Large \frac{1}{T} \large \int_0^{T/2} \Large \frac{d A_s}{dt} \normalsize dt \large \int_{\xi(t)}^{\xi(T-t)} \normalsize [s(x,t)-s(0,0)] dx , \qquad(13) [/math]

where [math]A_s(t) = b_s \eta (t) [/math] is the dead zone volume at time [math]t[/math] per unit estuarine length, [math] s(x,t)-s(0,0)\approx (x-\xi(t)) ds_0/dx[/math] and [math]\xi(t)[/math] is the net distance travelled by fluid parcels from the time of low water (LW). Other symbols are shown in figure 4. The integral evaluates mass transport due to water parcels passing through the plane [math]x=0[/math] during ebb but not during flood (because of a net seaward displacement related to storage in the dead zone, represented by the first term [math]s(x,t)[/math] between the square brackets), taking into account an equivalent landward water flow in the channel (second term [math]s(0,0)[/math] between the square brackets). By evaluating the integral we find for the coefficient [math]f_{dz}[/math] the expression [math]f_{dz} = \sin^2 \phi / (3 \pi^2)[/math].

A usual order of magnitude for the phase shift [math]T\phi/2 \pi[/math] is 30-60 minutes, yielding [math]f_{dz} \approx 0.005 [/math]. In estuaries with large tidal flats dead zones can significantly enhance longitudinal dispersion.

Dye experiments illustrating longitudinal dispersion by dead zones are shown in Estuarine dispersion: dye experiments in the Eastern Scheldt scale model.

Figure 4: Dispersion by an intertidal "dead zone" along a tidal channel. The figure illustrates the case of a phase shift [math]\phi[/math] between the vertical tidal motion ([math]d\eta /dt[/math]) and the horizontal tidal motion ([math]u(t)[/math]). The paths of two fluid parcels are shown, both starting from the same location at low water ([math]t=0[/math]). The first parcel (the square) follows the tidal motion in the channel, while the second parcel (the circle) is stored in the dead zone around high water in a time interval [math][t, T-t][/math]. Without mixing, the latter parcel returns to the channel before the former parcel has arrived at the same location. If particle paths in the main channel are given by [math]X(x,t)=x+\xi(t), \; \xi=(L/2)[\cos \phi - \cos (\omega t - \phi)], [/math] then the relative seaward displacement of particles leaving the dead zone at time [math]T-t[/math] is given by [math]\Delta X(t)=\xi(T-t)-\xi(t) .[/math] The result is longitudinal dispersion: a net relative displacement of the two fluid parcels during the tidal cycle.

Time scales for vertical and lateral mixing

A difficulty for practical use of the previous expressions for longitudinal dispersion, results from the uncertainty related to estimating the vertical and (especially) lateral mixing times, [math]T_z=D^2/K_z[/math] and [math]T_y=B^2/K_y[/math]. In case of a logarithmic velocity profile, the vertical diffusion coefficient is given by [math]K_z=0.4z(1-z/D)u_*[/math], where [math]u_*\approx 0.05 U[/math] is the friction velocity and [math]U[/math] the flow velocity. This yields a longitudinal dispersion coefficient [math]K_x \approx 6u_*D[/math], for steady flow [9]. However, in case of buoyant flows, vertical diffusion can be much slower (smaller [math]K_z[/math]), leading to stronger longitudinal dispersion. Lateral diffusion depends strongly on the geometry of the estuary. The lateral diffusion coefficient is generally expressed as [math]K_y \approx \alpha u_* D[/math]. An empirical estimate for moderately meandering channels is [math]\alpha \approx 0.6 [/math] [10] and a model estimate is [math] \alpha \approx 150 (B/ R)^2 [/math] [11], where [math]R[/math] is a characteristic channel bend radius.

Dispersion by deterministic chaos

Dye experiments show that dispersion in wide estuaries with complex geometry generally proceeds in an irregular way, by advection through a field of geometry-induced tidal eddies. The result is very different from diffusion by a cascade of turbulent eddies of progressively decreasing size. Parts of the dye can be trapped within gyres with almost no diffusion, while other dye patches can be highly stretched in the flow direction. Strong stretching occurs in particular in the interface zones between tidal eddies. Zimmerman (1986) [12] described the dispersion process in such systems as the result of Lagrangian chaos produced by the tidal whirlpool. Fluid parcels can be dispersed over the entire length of the estuary before lateral mixing has taken place. In this case, the random walk description of tidal dispersion is no longer valid. Zimmerman showed that longitudinal dispersion can still be described as a random process, even if turbulent mixing is completely absent. He called this random process “deterministic chaos” [13]. In his model, fluid parcels are dispersed by moving along chaotic orbits through a lattice of tidal eddies. Most dispersion is generated by eddies with a size [math]\lambda[/math] comparable to the tidal excursion length [math]L[/math] [14]. This suggests that the longitudinal dispersion coefficient for chaotic mixing should be proportional to

[math]K_x \propto UL \qquad(14) [/math].

The size of the eddies also depends on the basin with [math]B[/math]. A field study in Willapa Bay (US Pacific coast) suggests that chaotic dispersion could be described by a dispersion coefficient [math]K_x = 0.06 UB[/math] [15]. If the lateral mixing time [math]T_y[/math] is comparable to or larger than the flushing time [math]T_x [/math], the representation of the dispersive transport [math] Q_{disp}[/math] by the product of a dispersion coefficient and the local salinity gradient is no longer valid.

Dispersion by tidal pumping

Salt intrusion by tidal pumping is related to the higher average salinity of seawater entering the estuary during flood compared to the average salinity of estuarine water flowing out into the sea during ebb. It depends on the rate of renewal of estuarine water in the outflow region and therefore on tidal inflow-outflow hydrodynamics. Outflow of estuarine water often has a jet-like character, whereas flood water enters the estuary more distributed from different directions, depending on the tidal phase, see figure 5. The inflowing flood water therefore contains ‘new’ seawater from the sides of the ebb channel. Replacement of outflowing estuarine water by "new" seawater is enhanced when river discharge is high, because the ebb jet is concentrated in a surface layer (salinity stratification), whereas seawater inflow is more evenly distributed over the vertical.

Figure 5: Schematic representation of seawater intrusing by tidal pumping.

We call [math]\alpha[/math] the replacement rate of outflowing estuarine water by seawater during a tidal cycle. For small fresh water discharge, the corresponding dispersion coefficient at the estuarine mouth is given by

[math]K_{mouth} = \alpha \Large \frac{L^2 }{2T} , \normalsize \qquad(15) [/math]

where [math]L=\int_{flood} u(t)dt [/math] is the tidal excursion at the estuarine mouth. Savenije [16] derived the following empirical expression for [math]\alpha[/math]:

[math]\alpha=\Large \frac{2800 \pi D}{l_A} \normalsize \sqrt{Ri_E} , \qquad(16) [/math]

where [math]D[/math] is the depth and [math]l_A[/math] the convergence length of the estuary in the outflow zone (assuming exponential convergence of the cross-section in the outflow zone, [math] A(x) \sim exp(-x/l_A)[/math]);

[math]Ri_E[/math] is the Richardson estuary number [math]Ri_E=g \Delta \rho Q_R T^3 / ( \pi^2 \rho B L^3)[/math];

[math] \Delta \rho / \rho[/math] is the relative density difference seawater-fresh water and [math]B[/math] the estuarine width at the mouth. The value of [math]\alpha[/math] should not exceed 1. Tidal pumping is a major mechanism of seawater intrusion in estuaries during periods of high river flow.

Residence time scale

The residence time [math]T_r[/math] is defined as the average time a water parcel, which is initially located at a distance [math]x[/math] from the sea boundary, will take to leave the estuary. If the fresh water discharge is zero or very small, and if the dispersion coefficient [math]K_x[/math] is assumed constant along the estuary, the residence time is given by random walk theory [17]:

[math]T_r = \Large \frac{x^2}{2K_x} \normalsize \qquad(17) [/math].

The flushing time [math]T_f=T_x[/math] is the average time it takes for a fresh water parcel to move through the estuarine zone to the sea. According to the random walk model, for small discharge [math]Q_R[/math],

[math]T_f = \Large \frac{l^2}{2K_x} , \normalsize \qquad(18) [/math]

where [math]l[/math] is the estuarine length. This is approximately equivalent to [math]T_f = V_f / Q_R[/math] , where [math]V_f[/math] is the fresh water volume in the estuary.

Experimental determination of the longitudinal dispersion coefficient

The dispersion coefficient [math]K_x[/math] can be determined experimentally in situations where the freshwater discharge [math]Q_R[/math] is constant over a period longer than [math]T_x[/math]. In that case the salinity distribution [math]s(x,t)[/math] is close to equilibrium ([math] s(x,t)\approx s_0(x) [/math]). The total residual salt flux [math]Q_S[/math] approximately equals zero. We thus have (with the sign convention [math]Q_R \gt 0[/math])

[math]AK_x \Large \frac{ds_0}{dx} \normalsize + Q_R s_0 = 0 \qquad(19) [/math].

Values of the dispersion coefficient can be derived from measurement of the residual discharge [math]Q_R[/math] and the salinity distribution [math]s_0(x)[/math]. Examples of longitudinal dispersion coefficients determined in this way are shown in table 1. It should be noticed that the dispersion coefficient [math]K_x[/math] is a function of [math]x[/math] and [math]Q_R[/math]. The dependence of [math]K_x[/math] on [math]Q_R[/math] has two causes. It is related in the first place to the influence of the salinity distribution on the velocity flow field [math]u(x,u,z,t)[/math]; such an influence is due to salinity-induced density gradients (see Estuarine circulation). In the second place, it is related to the location of the freshwater-seawater transition zone. If this zone is situated near the estuarine mouth, the dispersion coefficient is strongly influenced by tidal pumping. This explains the high longitudinal dispersion coefficients for Rotterdam Waterway, Seine and Loire in table 1, which are determined for situations with important river flow [math]Q_R/hb[/math]. The same holds, to a somewhat lesser degree, for the Elbe, Weser, Mekong and Sinnamary.

In estuaries with a complex geometry and river flow [math]Q_R/hb[/math] several orders of magnitude smaller than the tidal velocity, the influence of salinity-induced density gradients on the longitudinal dispersion coefficient is generally small. This is often the case for tidal lagoons with small river inflow.

If a non-buoyant dissolved substance is introduced in the estuary, it will be mixed over the cross-section after a time [math]T_A[/math] . From that time, the longitudinal dispersion of the substance is similar to salinity dispersion (same dispersion coefficient). For a permanent discharge of a non-buoyant dissolved substance, the same dispersion coefficient applies in the estuarine zones where the substance is mixed over the estuarine cross-section.

Longitudinal dispersion coefficients derived from observed salinity distributions at constant river discharge. The figures for tidal range, depth and width are representative values for the zone with the strongest salinity gradient. Data from [18], [19], [20], [21], [22], [23], [24].
estuary tidal range [math]2a[/math] [m] depth [math]D[/math] [m] width [math]B[/math] [km] discharge [math]Q_R[/math] [m3/s] dispersion coefficient [math]K_x[/math] [m2/s]
Bay of Fundy (Canada) 10 20 20 150 300
Bristol Channel (UK) 8 30 20 480 60
Chao Phraya (Thailand) 2.5 7.2 0.6 30 330
Corantijn (Surinam) 4.3 6.5 3 500 230
Delaware (US) 1.5 6.6 7 300 300
Eastern Scheldt (Netherlands) 3 12.5 2 60 200
Elbe (Germany) 3.3 12 2.5 750 700
Ems-Dollard (Netherlands) 3 9 4 100 275
Gambia (The Gambia) 1.2 8.7 4 2 200
Hudson (US) 1.6 11,6 2.2 100 110
Humber (UK) 5.5 12 3 250 300
Incomati (Mozambique) 5.5 2.9 0.6 1 10
Limpopo (Mozambique) 2.6 7 0.2 5 150
Loire (France) 4.5 9 0.9 825 900
Mae Klong (Thailand) 2 5.2 0.2 30 200
Maputo (Mozambique) 6.7 3.6 1.3 10 100
Mekong-Co Chien+Cung Hau (Vietnam) 2.1 7 4 2125 570
Mekong-Tran De+Dinh Anh (Vietnam) 2.8 8 3 2250 530
Mersey (UK) 7.5 20 1 80 400
Potomac (US) 1.4 8.4 9 110 70
Pungue (Mozambique) 5 11.5 1.8 20 140
Rotterdam Waterway (Netherlands) 0.9 15 0.6 1000 1000
St. Lawrence (Canada) 3 74 48 8500 200
Seine (France) 5.5 8 0.8 440 800
Sinnamary (Guiana) 2.3 3.8 0.3 100 560
Solo (Indonesia) 1.1 9.2 0.17 10 240
Tha Chin (Thailand) 2.9 5.3 0.2 10 270
Thames (UK) 4.5 12 3 60 100
Weser (Germany) 3.8 9 2 324 1000
Western Scheldt (Netherlands) 3.8 16 3.5 100 200

Related articles

Estuarine dispersion: dye experiments in the Eastern Scheldt scale model

Estuarine circulation

Salt wedge estuaries

Morphology of estuaries

Physical processes and morphology of synchronous estuaries

Ocean and shelf tides


  1. Taylor, G.I., 1921, Diffusion by Continuous Movements. Proc., London Math. Soc., Ser. A 20: 196-211
  2. Dronkers, J. 1982. Conditions for gradient-type dispersive transport in one-dimensional tidally averaged transport models. Est.Coast.Shelf Sci. 14: 599-621
  3. Taylor, G.I. 1954. The dispersion of matter in turbulent flow through a pipe. Procs. Royal Society Londin A223: 446-468
  4. Fischer, H.B., List, E.J., Koh, R.C.Y., Imberger, J. and Brooks, N.H. 1979. Mixing in Inland and Coastal Waters. Academic Press, New York
  5. Smith, R. 1980. Buoyance effects upon longitudinal dispersion in wide well-mixed estuaries. Philos. Trans. Royal Soc. London A 296: 467-496
  6. Holley, E.R., Harleman, D.R. and Fischer, H.B. 1970. Dispersion in homogeneous estuary flow. J. Hydr. Div. ASCE 96: 1691-1706
  7. Okubo, A. 1967. The effect of shoreline irregularities on horizontal diffusion from an instantaneous source. Inter. J. Oceanol. Limnol. 1: 194-204
  8. Dronkers, J. 1978. Longitudinal dispersion in shallow well-mixed estuaries. Procs. 16th Int. Conf. Coastal Eng. 3: 2761-2777
  9. Elder, J.W. 1959. The Dispersion of Marked Fluid in Turbulent Shear Flow. J. Fluid Mech. 5: 544-560
  10. Fischer H.B. 1972. Mass transport mechanisms in partially stratified estuaries. J. Fluid Mech. 53: 671–687
  11. Yotsukura, N. and Sayre, W.W. 1976. Transverse mixing in natural channels. Water Resources Res. 12: 695–704
  12. Zimmerman, J.T.F. 1986. The Tidal Whirlpool: A Review of Horizontal Dispersion by Tidal and Residual Currents. Neth. Journal of Sea Research 20:133-154
  13. Ridderinkhof, H. and Zimmerman, J. T. F. 1992. Chaotic stirring in a tidal system. Science 258: 1107-1109
  14. Zimmerman, J.T.F. 1976. Mixing and flushing of tidal embayments in the western Wadden Sea, I: Distribution of salinity and calculation of mixing time scales. Neth.J.Sea Res. 10:149-191
  15. Banas, N.S., Hickey, B.M., 2005. Mapping exchange and residence time in a model of Willapa Bay, Washington, a branching, macrotidal estuary. Journal of Geophysical Research 110, C11011. doi:10.1029/2005JC002950
  16. Savenije, H. H. G. 2005. Salinity and Tides in Alluvial Estuaries. Elsevier, Amsterdam, 197 pp.
  17. Zimmerman, J.T.F. 1981 The flushing of well mixed tidal lagoons and its seasonal fluctuations. UNESCO Tech. Pap. Mar. Sci. 33: 15-26
  18. Prandle, D. 2004. Saline intrusion in partially mixed estuaries. Estuarine, Coastal and Shelf Science 59; 385-397
  19. Vandenbruwaene, W., Plancke, Y., Verwaest,T. and Mostaert F. 2013. Interestuarine comparison: Hydro-geomorphology Hydro- and geomorphodynamics of the TIDE estuaries Scheldt, Elbe, Weser and Humber. TIDE Report Flanders Hydraulics Research WL 2013-770
  20. Van Rijn, L. 2011. Comparison Hydrodynamics and Salinity of Tide Estuaries: Elbe, Humber, Scheldt and Weser. TIDE Report, Deltares 1203583-000
  21. Holloway, P.E. 1981. Longitudinal Mixing in the Upper of the Bay of Fundy Reaches. Estuarine, Coastal and Shelf Science I3: 495-515
  22. Helder, W. and Ruardij, R. 1982. A one-dimensional mixing and flushing model of the Ems-Dollard estuary: calculation of time scales at different river discharges. Neth. J. Sea Res. 15: 293-312
  23. Nguyen, A.D. 2008. Salt intrusion, tides and mixing in multi-channel estuaries. PhD thesis Delft University
  24. Publications GIP Seine-aval and GIP Loire-estuaire

The main author of this article is Job Dronkers
Please note that others may also have edited the contents of this article.

Citation: Job Dronkers (2019): Seawater intrusion and mixing in estuaries. Available from [accessed on 18-10-2019]